Remove as much of the asphalt as possible by blotting with a white paper towel or scraping with a dull knife.

Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never use a circular motion to remove the spot as this may destroy the texture. Stop if spot is removed. If not, continue with the next step.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent solution and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary.

Apply pad of paper towels and weight down with brick.

Remove as much of the spill as is possible by blotting with white paper towels or scraping with a dull knife. A wet vacuum is useful if a large quantity of liquid was spilled. If spot has dried, saturate the tufts in the affected area with tap water (do not overwet). Allow to remain for about 1 minute and blot. If the spot is being removed using water, continue until the spot is completely removed. Blot dry and apply the paper towels and brick. If it is not completely removed go to the next step.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Remove as much of the stain as possible by blotting with a white paper towel, then neutralize with an ammonia solution (1 tablespoon of clear household ammonia to 1/2 cup of water.). Saturate spot with the ammonia solution using a spray bottle. Do not wet backing. Blot with a white paper towel to remove excess moisture. All solutions for removing blood must be cool.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Spread brown paper (such as grocery bag) or a terry cloth towel over the area and iron with the setting on warm. The wax will be absorbed into the paper or towel.

Remove any traces with alcohol or dry cleaning fluid.

Remove as much of the candy as possible by blotting with a white paper towel or scraping with a dull knife.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Remove as much of the stain as possible by blotting with a white paper towel or scraping with a dull knife, then neutralize with an ammonia solution (1 tablespoon of clear household ammonia to 1/2 cup of water). Saturate spot with the ammonia solution using spray bottle. Do not wet backing. Blot with a white paper towel to remove excess moisture.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Freeze the gum using an ice cube.

Shatter the frozen gum with a knife handle and vacuum. Some citrus based products such as De-Solv-It® or Orange-Sol® have been demonstrated to break down the stickiness of gum so that it can be removed.

Blot up as much of the spill as is possible. A wet vacuum is useful if a large quantity of liquid was spilled.

If spot has dried, saturate the tufts in the affected area with tap water (do not overwet). Allow to remain for about 1 minute and blot. If the spot is being removed using water, continue until the spot is completely removed. Blot dry and apply the paper towels and brick. If the stain is not completely removed, continue.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Acid toilet bowl cleaners, acne medication, alkaline drain cleaners, chlorinated bleach, hair dyes, iodine, insecticides, mustard with turmeric, plant fertilizers and stains of this nature cannot be removed as they have permanently altered the carpet's color. Call a professional. Most likely the only solution is to insert carpet from a closet, or some other area into the area where the spot is cut out.

Remove as much of the stain as possible by blotting with white paper towel or scraping with a dull knife, then neutralize with an ammonia solution (1 tablespoon of clear household ammonia to 1/2 cup of water). Saturate spot with ammonia solution using spray bottle. Do not wet backing. Blot with a white paper towel to remove excess moisture. All solutions for removing chocolate must be cool.

Remove as much of the spill as possible by blotting with a white paper towel or scraping with a dull knife.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Blot with a white paper towel to remove as much of the stain as possible then neutralize with the white vinegar solution (1/3 cup WHITE vinegar to 2/3 cup of water). Saturate spot with white vinegar solution, using a spray bottle and blot to remove excess moisture.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Blot with white paper towel to remove as much of the stain as possible then neutralize with an ammonia solution (1 tablespoon of clear household ammonia to 1/2 cup of water). Saturate spot using spray bottle. Do not wet backing. Blot with a white paper towel to remove excess moisture.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Blot with white paper towel to remove as much of the stain as possible then neutralize with an ammonia solution (1 tablespoon clear household ammonia to 1/2 cup of water). Saturate spot with the ammonia solution using spray bottle. Do not wet backing. Blot with a white paper towel to remove excess moisture.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Remove as much of the crayon as possible by blotting with a white paper towel or scraping with a dull knife.

Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never us a circular motion to remove spot as this may destroy the texture. Stop if spot is removed. If not, go to the next step.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture, spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Allow mud to dry completely.

Shatter the dried mud with the handle of a knife and vacuum. Remove as much of the mud as possible by blotting with a white paper towel or scraping with a dull knife.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Remove as much of the excess liquid or dried stain as possible by using a spoon or dull knife. Then blot up as much of the stain as possible using a blotting motion.

Neutralize by spraying the affected area with an ammonia solution (1 tablespoon of clear household ammonia and 1/2 cup of water). Care should be taken to remove all protein matter.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Remove as much of the ice cream as possible by blotting with a white paper towel or scraping with a dull knife.

Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never us a circular motion to remove spot as this may destroy the texture. Stop if spot is removed. If not, go to the next step.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Remove as much of any foreign material as possible by blotting with a white paper towel or scraping with a dull knife.

Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never us a circular motion to remove spot as this may destroy the texture. Stop if spot is removed. If not, go to the next step.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Remove as much of the foreign material as possible by blotting with a white paper towel or scraping with a dull knife.

Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never us a circular motion to remove spot as this may destroy the texture. Stop if spot is removed. If not, go to the next step.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Remove as much of the milk as possible by blotting with a white paper towel or scraping with a dull knife.

Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never us a circular motion to remove spot as this may destroy the texture. Stop if spot is removed. If not, go to the next step.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Blot with white paper towel to remove as much of the stain as possible then neutralize with an ammonia solution (1 tablespoon of clear household ammonia to 1/2 cup of water). Saturate spot using spray bottle. Do not wet backing. Blot with a white paper towel to remove excess moisture.

Apply a small quantity of detergent solution to the spot. Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Blot with white paper towel to remove as much of the stain as possible then neutralize with an ammonia solution (1 tablespoon of clear household ammonia to 1/2 cup of water). Saturate spot using spray bottle. Do not wet backing. Blot with a white paper towel to remove excess moisture.

Apply a small quantity of detergent solution to the spot. Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Allow mud to dry completely. Shatter the dried mud with the handle of a knife and vacuum.

Remove as much of the mud as possible by blotting with a white paper towel or scraping with a dull knife.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Acid toilet bowl cleaners, acne medication, alkaline drain cleaners, chlorinated bleach, hair dyes, iodine, insecticides, mustard with turmeric, plant fertilizers and stains of this nature cannot be removed as they have permanently altered the carpet's color. Call a professional. Most likely the only solution is to insert carpet from a closet, or some other area into the area where the spot is cut out.

Remove as much of the nail polish as possible using a spoon or dull knife.

Apply a non-oily nail polish remover to a clean white cloth and gently rub (in only one direction at a time) or blot the spot. Continue until spot is removed. Do not allow nail polish remover to get to the latex backing. Go to the next step to remove nail polish remover.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Remove as much of the foreign material as possible by blotting with a white paper towel or scraping with a dull knife.

Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never us a circular motion to remove spot as this may destroy the texture. Stop if spot is removed. If not, go to the next step.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture, spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Remove as much of the foreign material as possible by blotting with a white paper towel or scraping with a dull knife.

Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never us a circular motion to remove spot as this may destroy the texture. Stop if spot is removed. If not, go to the next step.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Remove as much of the foreign material as possible by blotting with a white paper towel or scraping with a dull knife.

Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never us a circular motion to remove spot as this may destroy the texture. Stop if spot is removed. If not, go to Step 3.

Blot up as much of the spill as possible by blotting with a white paper towel or scraping with a dull knife.

Apply a small quantity of detergent solution to the spot. Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Blot with a white paper towel to remove as much of the stain as possible.

Neutralize with the white vinegar solution (1/3 cup of WHITE vinegar in 2/3 cup of water). Saturate spot with the white vinegar solution, using a spray bottle and blot to remove excess moisture.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Remove as much of the foreign material as possible by blotting with a white paper towel or scraping with a dull knife.

Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never us a circular motion to remove spot as this may destroy the texture. Stop if spot is removed. If not, go to the next step.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Saturate spot with lemon juice, using a spray bottle, and allow to remain for 5 minutes. Then go to the next step to remove lemon juice. If this does not work, and it may not, call a professional. Most rust removers contain a very strong acid and are, therefore, not recommended for use by homeowners.

Blot up as much of the liquid with a white paper towel.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Remove as much of the foreign material as possible by blotting with a white paper towel or scraping with a dull knife.

Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never us a circular motion to remove spot as this may destroy the texture. Stop if spot is removed. If not, go to the next step.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Remove as much of the foreign material as possible by blotting with a white paper towel or scraping with a dull knife.

Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never us a circular motion to remove spot as this may destroy the texture. Stop if spot is removed. If not, go to the next step.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Blot with white paper towel to remove as much of the stain as possible then neutralize with an ammonia solution (1 tablespoon of clear household ammonia and 1/2 cup of water). Saturate spot with the ammonia solution using spray bottle. Do not wet backing. Blot with a white paper towel to remove excess moisture.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Vacuum, using crevice tool of vacuum cleaner to remove the soot. If all, or most, of the soot has not been removed, call a professional cleaner. If vacuuming has removed all particles go to the next step. Remove as much of the foreign material as possible by blotting with a white paper towel or scraping with a dull knife.

Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never us a circular motion to remove spot as this may destroy the texture. Stop if spot is removed. If not, go to the next step.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Blot with white paper towel to remove as much of the stain as possible. Neutralize with an ammonia solution (1 tablespoon of clear household ammonia in 1/2 cups of water). Saturate spot with ammonia solution using spray bottle. Do not wet backing. Blot with a white paper towel to remove excess moisture.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Remove as much of the tar as possible by blotting with a white paper towel or scraping with a dull knife.

Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never us a circular motion to remove spot as this may destroy the texture. Stop if spot is removed. If not, go to the next step.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture, spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Remove as much of the stain as possible by blotting with a white paper towel or scraping with a dull knife.

Neutralize with an ammonia solution (1 tablespoon of clear household ammonia and 1/2 cup of water). Saturate spot with ammonia solution using spray bottle. Do not wet backing. Blot with a white paper towel to remove excess moisture.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

For Customers With ECOSTEAM'S Consumer Product:

Bottom Line

For The Treatment of Urine, Vomit, Excrement Odors

Please Carefully Follow Label Directions

If The Situation Is Severe, Than Call Ecosteam Immediately For Professional Remediation.

If you do not have Bottom Line® Call Ecosteam at any of the phone numbers listed or simply go to the Consumer Products page and place your order online.

Otherwise follow the directions listed below:

Remove as much of the stain as possible by using a spoon or dull knife. And, blot up as much of the stain as possible with white paper towels.

Neutralize by spraying the affected area with the ammonia solution (1 tablespoon of clear household ammonia and 1/2 cup of water). Care should be taken to remove all protein matter. Blot to remove excess moisture.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick. Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.

If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

For Customers With ECOSTEAM'S Consumer Product:

Bottom Line

For The Treatment of Urine, Vomit, Excrement Odors

Please Carefully Follow Label Directions

If The Situation Is Severe, Than Call Ecosteam Immediately For Professional Remediation.

If you do not have Bottom Line® Call Ecosteam at any of the phone numbers listed or simply go to the Consumer Products page and place your order online.

Otherwise follow the directions listed below:

Remove as much of the stain as possible by using a spoon or dull knife. Blot up as much of the stain as possible with white paper towels.

Neutralize by spraying the affected area with the ammonia solution (1 tablespoon of clear household ammonia and 1/2 cup of water). Care should be taken to remove all protein matter. Blot to remove excess moisture.

Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn® and Joy®.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.

Rinse with tap water using a spray bottle, blot to remove excess moisture.

Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry. If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Blot to remove excess liquid or stain.

Wet stain with small amount of alcohol or dry cleaning solvent and blot dry immediately. Repeat until no stain is on paper towel.

If fabric stain is persistent wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain. Wet fabric with minimum amount of water, soak 1 minute, and blot with paper towel. Repeat water/blot procedure until no stain is evident on towel, and then blot dry.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain. Wet fabric with minimum amount of water, soak 1 minute, and blot with paper towel. Repeat water/blot procedure until no stain is evident on towel, and then blot dry.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain. Wet fabric with minimum amount of water, soak 1 minute, and blot with paper towel. Repeat water/blot procedure until no stain is evident on towel, and then blot dry.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain. Wet fabric with minimum amount of water, soak 1 minute, and blot with paper towel. Repeat water/blot procedure until no stain is evident on towel, and then blot dry.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain. Wet stain with small amount of alcohol or dry cleaning solvent and blot dry immediately. Repeat until no stain is on paper towel.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain.

Wet stain with small amount of alcohol or dry cleaning solvent and blot dry immediately. Repeat until no stain is on paper towel.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain. Carefully wet stained area with "7-Up" or tonic water and blot with paper towel. Repeat wetting and blotting until no stain is evident on towel. Rinse with clear water and blot dry.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

If fabric stain is persistent, apply 3% hydrogen peroxide. Let stand four hours and blot. Reapply 3% hydrogen peroxide, allow to stand 24 hours. Blot and allow to air dry for 48 hours.

If stain is still evident, repeat with hydrogen peroxide. When stain is no longer visible, rinse with clear water and blot dry.

Blot to remove excess liquid or stain. Wet stain with small amount of alcohol or dry cleaning solvent and blot dry immediately. Repeat until no stain is on paper towel.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain. Wet fabric with minimum amount of water, soak 1 minute, and blot with paper towel. Repeat water/blot procedure until no stain is evident on towel, and then blot dry.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Remove excess stain with dull-edge spoon or spatula.

Wet fabric with 3% acetic acid (50% white vinegar, 50% water) and brush off particulate matter. Reapply 3% acetic acid and blot with paper towel. Repeat until stain is removed.

Rinse with clear water and blot dry. If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Blot to remove excess liquid or stain. Wet fabric with minimum amount of water, soak 1 minute, and blot with paper towel. Repeat water/blot procedure until no stain is evident on towel, and then blot dry.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain. Wet stain with small amount of alcohol or dry cleaning solvent and blot dry immediately. Repeat until no stain is on paper towel.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain. Wet fabric with minimum amount of water, soak 1 minute, and blot with paper towel. Repeat water/blot procedure until no stain is evident on towel.

Apply 3% hydrogen peroxide plus household ammonia and blot. Rinse with clear water and blot dry.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/ water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Blot to remove excess liquid or stain. Carefully wet stained area with "7-Up" or tonic water and blot with paper towel. Repeat wetting and blotting until no stain is evident on towel. Rinse with clear water and blot dry.

If fabric stain is persistent go to wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

If fabric stain is persistent, apply 3% hydrogen peroxide. Let stand four hours and blot. Reapply 3% hydrogen peroxide, allow to stand 24 hours. Blot and allow to air dry for 48 hours.

If stain is still evident, repeat with hydrogen peroxide. When stain is no longer visible, rinse with clear water and blot dry.

Blot to remove excess liquid or stain. Wet stain with small amount of alcohol or dry cleaning solvent and blot dry immediately. Repeat until no stain is on paper towel.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain. Wet stain with small amount of alcohol or dry cleaning solvent and blot dry immediately. Repeat until no stain is on paper towel.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry

Blot to remove excess liquid or stain. Wet fabric with minimum amount of water, soak 1 minute, and blot with paper towel. Repeat water/blot procedure until no stain is evident on towel, and then blot dry.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain. Wet fabric with minimum amount of water, soak 1 minute, and blot with paper towel. Repeat water/blot procedure until no stain is evident on towel, and then blot dry.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain. Wet stain with small amount of alcohol or dry cleaning solvent and blot dry immediately. Repeat until no stain is on paper towel.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain. Wet stain with small amount of alcohol or dry cleaning solvent and blot dry immediately. Repeat until no stain is on paper towel

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain. Wet fabric with minimum amount of water, soak 1 minute, and blot with paper towel. Repeat water/blot procedure until no stain is evident on towel, and then blot dry.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot excess. Apply small amount of nail polish remover and blot immediately. Repeat until no slain is evident on paper towel.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Blot to remove excess liquid or stain. Carefully wet stained area with "7-Up" or tonic water and blot with paper towel. Repeat wetting and blotting until no stain is evident on towel. · Rinse with clear water and blot dry. If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

If fabric stain is persistent, apply 3% hydrogen peroxide. Let stand four hours and blot. Reapply 3% hydrogen peroxide, allow to stand 24 hours. Blot and allow to air dry for 48 hours. If stain is still evident, repeat with hydrogen peroxide.

When stain is no longer visible, rinse with clear water and blot dry.

Blot to remove excess liquid or stain. Wet fabric with minimum amount of water, soak 1 minute, and blot with paper towel. Repeat water/blot procedure until no stain is evident on towel, and then blot dry.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain. Wet stain with small amount of alcohol or dry cleaning solvent and blot dry immediately. Repeat until no stain is on paper towel.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Blot to remove excess liquid or stain.

Carefully wet stained area with "7-Up" or tonic water and blot with paper towel. Repeat wetting and blotting until no stain is evident on towel. · Rinse with clear water and blot dry.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

If fabric stain is persistent, apply 3% hydrogen peroxide. Let stand four hours and blot. Reapply 3% hydrogen peroxide, allow to stand 24 hours. Blot and allow to air dry for 48 hours.

If stain is still evident, repeat with hydrogen peroxide.

When stain is no longer visible, rinse with clear water and blot dry.

Blot to remove excess liquid or stain.

Wet fabric with minimum amount of water, soak 1 minute, and blot with paper towel. Repeat water/blot procedure until no stain is evident on towel, and then blot dry.

If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.

Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.

Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.